Quick Answer: How Do You Access The Console Of A Switch?

What is a console cable used for?

Rollover cable (also known as a Yost cable, Cisco cable, or a Console cable) is a type of null-modem cable that is often used to connect a computer terminal to a router’s console port.

This cable is typically flat (and has a light blue color) to help distinguish it from other types of network cabling..

How do you reset a switch in PuTTY?

How to reset the switch to the default factory settings using…Go to the website https://www.putty.org/ to download PuTTY on the PC. … Start puTTy on the PC and configure the terminal emulation program as follows: … Power on the switch. … Enter the corresponding number of the Reset option, which is 2 in this example, and enter Y to confirm the choice. … Log in to the switch again.

How do I console my HP switch?

To connect a console to the switch, use the console cable shipped with the switch and connect a PC or VT-100 terminal to the console serial port….Reconfigure the switch and save the new settings.Reconfigure the terminal and save the new settings.Reboot the switch and re-establish the console session.

How do I bring up a console switch?

Make sure that you have correct console connection to Cisco Router or Switch. Connect the RJ45 jack of your console cable to the console port of your Cisco Router or Switch. Connect the other end to the Serial port of your computer. Refer the following link to know more about console port and console cable.

How do I configure a switch?

How to configure Cisco switch?Initial command prompt “Switch>” appears on the screen.Type “enable” next to it and press “Enter”.This will take you into the “EXEC” mode, also known as the Global Configuration mode.Go into configure mode using configure terminal.Enter the configuration commands one per line.

What is the difference between console and auxiliary port?

Console cable is normally used to connect to the router using a terminal emulation program like HyperTerminal. AUX port is usually used to get dial-in access to the router. You connect one end of the console cable to the router, and other end to the serial interface of your PC.

How do I remotely connect to a Cisco switch?

Step 1 From the remote host, enter the telnet command and the name or IP address of the switch you want to access. Step 2 At the prompt, enter the password for the CLI. If no password has been configured, press Return. Step 3 Enter the necessary commands to complete your desired tasks.

How do I access a Cisco switch?

When you log in for the first time, the Accessing Cisco Switch page appears. On the Accessing Cisco Switch page, click the Wireless Web GUI link to access switch web GUI Home page. Choose Configuration > Wizard to perform all steps that you need to configure the switch initially.

How do I access the console on my router?

Access router command line interface using Windows laptopUnder Category, choose Session.Under Connection type, choose Serial.In the Serial line, enter the COM port on your laptop that is connected to the console port on your router, using the console cable.Click Open.

How do I use PuTTY as a console switch?

Configure putty to be able to communicate with the router over the USB port ( /dev/ttyUSB0 ).run sudo putty.Click on Serial for the Connection Type:Set the serial line to /dev/ttyUSB0.Click on Keyboard, then set backspace key to Control-H.Click on Session . Click on Default Settings. Click Save .Click Open .

What is console port on switch?

Console port is used to connect a computer directly to a router or switch and manage the router or switch since there is no display device for a router or switch . … A special type of cable, known as roll over cable is used to connect the Serial/COM port of the computer to the router or switch console port.

What is the difference between console port and management port?

A management port can be used for remote management and configuration of a networking device, where as the Console Port can be used, in conjunction with a console server, such as Lantronix SLC 8000, to implement a separate dedicated network to access the network devices in case the primary network goes down.

How do I login to a switch?

Enter the IP address of the switch in the Host Name field and keep the default value 22 in the Port field; select SSH as the Connection type. Click Open. 2)Enter the login username and password to log in to the switch, and you can continue to configure the switch.

How do I configure a manageable switch?

Create the VLANs.Log in to the management page of the switch.Go to Routing – VLAN – VLAN Static Routing Wizard.Enter the VLAN ID, the IP Address and the Network Mask for the VLAN. … Select the ports to add to the VLAN. … Click Apply. … When prompted with the Global IP routing mode window, click OK.More items…